How To Apply Gluvit To Aluminum Boat

Gluvit is a waterproof sealant that is used to protect surfaces from water damage and corrosion. Applying Gluvit to an aluminum boat will help ensure its longevity and keep it looking great for years to come. The process of applying Gluvit may seem intimidating, but with the right tools and materials on hand, it’s actually quite simple. In this article, you’ll learn how to properly apply Gluvit to your aluminum boat so it can stay in perfect condition for as long as possible!

Gather Necessary Tools and Materials

To get the job done right, you’ll need to gather up all the right materials and tools, so let’s get started! You’ll need cleaning supplies like a scrub brush, mild soap, and a sponge. To ensure your aluminum boat is properly protected from the elements, make sure you have an appropriate surface protection product designed for aluminum boats like Gluvit epoxy waterproof sealer. You may also need some painter’s tape to mask off areas that don’t need Gluvit applied. It’s essential that you have all these items on hand before beginning any application process.

You should also make sure that your aluminum boat is cleaned and dried thoroughly before applying Gluvit. This will help to ensure that the sealant adheres properly and provides maximum protection for your boat. Be sure to look for any cracks or other signs of damage in the hull as well; if there are any then they must be addressed before starting with Gluvit. Finally, it’s important to read through all instructions included with your Gluvit purchase carefully before beginning application process – this will help guarantee successful results when using it on your aluminum boat.

Prepare the Boat’s Surface

Before you can begin working on your vessel, its surface must be carefully prepped in order to ensure the best results. To do this, start by cleaning the boat with a brush and water. Be sure to get rid of any dirt, grease or grime that may have accumulated on its surface. If necessary, use a degreaser to remove stubborn deposits and stains. Once the boat is clean and dry, use sandpaper or steel wool to lightly scour it until all rust spots are removed and the metal is smooth and shiny.

After completing these steps, check for any cracks or holes in the hull that need repairing before applying Gluvit. If needed, patch up these areas using epoxy resin then sand them down until they are flush with the rest of the boat’s surface. Once everything is ready, wipe down the entire vessel one last time with a damp cloth to make sure there’s no dust left behind before beginning your Gluvit project.

See also  How To Adjust Boat Lift Cables

Finally, apply a coat of primer suitable for aluminum boats over all exposed metal surfaces as this will help ensure better adhesion when applying Gluvit later on. Allow it to dry completely before proceeding with your project according to instructions provided by manufacturer’s guidelines.

Mix Gluvit

Now it’s time to mix up Gluvit and get ready to create a waterproof seal for your vessel. Before you begin, make sure that you are wearing protective gloves and eye wear to prevent any irritation or injury. It is also important to work in a well-ventilated area as the fumes from Gluvit can be harmful if inhaled.

To mix the Gluvit properly, start by combining equal parts of the resin base and hardener together in a clean container. Using a stir stick, blend the mixture thoroughly until it has an even consistency throughout with no lumps or streaks. It is important to ensure that all materials are completely blended together as this will determine how effective of a bond you achieve when applying it to your boat’s surface.

Next, add enough thinner until the mixture reaches a creamy paint-like consistency—about the same thickness as latex paint. Once everything is mixed together, let it sit for about five minutes before using so that air bubbles can escape from within the mixture before being applied to your vessel’s surface.

Apply Gluvit

Put on your protective gear and grab a brush, it’s time to create a waterproof seal with Gluvit! Before applying Gluvit, you must make sure the surface is clean and free of dirt, rust or any other debris. This can be achieved by brushing the area with a wire brush or sandpaper and then wiping it down with an acetone-based solvent. Once the surface is prepared, apply Gluvit to protect against rust and moisture damage.

Use a paintbrush that is small enough to fit into cracks and crevices that are hard to reach. Make sure each layer is evenly spread out across the entire surface area. Apply at least three coats of Gluvit in order to get maximum protection from harsh weather conditions. Allow each coat to dry thoroughly before adding additional layers – this will ensure optimum adhesion between coats.

Applying Gluvit takes patience as well as time for proper application and thorough drying times between coats. However, once properly applied it can provide lasting protection for your aluminum boat from corrosion and water damage for years to come!

Allow Gluvit to Cure

Once you’ve finished applying the coating, let it sit for at least 24 hours to give it time to fully cure. Proper ventilation is essential during this process, so make sure the boat is in an area with good air flow. You should also take into account the weather conditions; if it’s raining or extremely humid outside, you may need to wait a few extra days for the Gluvit coating to set properly.

See also  How To Bring A Boat From Usa To Canada

If possible, store your boat indoors during this period as temperatures above 90°F can cause the curing process to slow down significantly. Additionally, try not to move your boat while the Gluvit has yet to dry completely; any shocks or vibrations could interfere with its integrity and affect how well it holds up over time.

Before using your boat again, test out the newly applied Gluvit by running your hands along its surface. Make sure there are no rough patches or areas where the coating still feels damp before going out on the water. If everything looks and feels good, then you can enjoy peace of mind knowing that your aluminum boat is prepped and ready for use!

Frequently Asked Questions

How long will Gluvit last on an aluminum boat?

Gluvit is a popular choice for coating aluminum boats. It provides a waterproof, protective seal that can last up to 10 years if properly applied. Before applying Gluvit, it’s important to remember to prepare the surface with sandpaper and cleaning agents in order to ensure that the product adheres correctly. The longevity of Gluvit also depends on environmental conditions, as extreme temperatures or sun exposure can cause it to wear off more quickly. To get the best results from Gluvit on your aluminum boat, take care to apply it according to manufacturer instructions and protect it from the elements where possible.

Can Gluvit be used on other materials?

Gluvit is a specialized epoxy sealant that can be used to protect and waterproof aluminum boats, but it can also be used on other types of boats. The sealant works by creating a barrier that prevents water from penetrating the surface of the boat and causing damage, such as rusting or corrosion. Gluvit can also be used on wooden boats, fiberglass boats, and metal boats made from different materials to provide protection against moisture and UV rays. To apply Gluvit to any type of material, you will need to make sure the surface is clean and free of dirt or debris before applying an even coat using either a brush or roller. Once applied, the sealant should last for several years with minimal maintenance required.

See also  How To Buy Boat From Private Seller

How much Gluvit is needed to cover an aluminum boat?

When it comes to protecting and waterproofing your aluminum boat, Gluvit is an excellent choice. To properly apply Gluvit to an aluminum boat, you’ll need to begin by preparing the surface – make sure any dirt or debris is removed and the area is dry before continuing. Then, apply a generous coating of Gluvit along all seams and other areas to be treated. Depending on the size of your boat, you may need several quarts of Gluvit in order to cover it completely. Allow the product time to fully cure before using your boat in any type of water environment.

What is the best temperature to apply Gluvit?

For best results when applying Gluvit to your aluminum boat, you should make sure the temperature is between 65 and 85 degrees Fahrenheit. Temperature can affect the performance of Gluvit, so it’s important to make sure you have the right conditions before beginning. Additionally, preparing the surface of your boat is key for a successful application – this includes cleaning off any residue or dirt and lightly sanding down any areas with rough patches or rust. Proper paint preparation will also help ensure that Gluvit adheres correctly to your aluminum boat.

Does Gluvit require any special maintenance?

Once Gluvit is applied to your aluminum boat, you should take certain steps to ensure that the coating remains in good condition. Before applying Gluvit, it’s important to make sure the surface of your boat is properly prepared. You’ll need to use a scrub brush and soapy water to remove any dirt or grime from the surface. Make sure you dry the area completely before applying Gluvit. After application, you should regularly inspect the coated areas for signs of damage or wear and tear that may have occurred over time. If there are any signs of damage, repair them promptly with an appropriate sealant or patching material. Additionally, you can apply additional coats of Gluvit every few years in order to maintain a strong protective barrier around your boat.


To conclude, applying Gluvit to an aluminum boat is a straightforward process. All you need is the right materials and tools. First, prep the surface of your boat so that it’s ready for application. Then mix up the Gluvit and apply it evenly over the entire surface. Allow it to dry completely before taking your boat back out on the water. With just a bit of effort, you can protect your aluminum boat from corrosion and keep it in top-notch condition for years to come!

Scroll to Top